·电 话:0515-82239399
·传 真:0515-82288488
·联系人:潘经理 
·手 机:13851133868 
·地 址:盐城市沿河中路13号
·邮 编:224001
  产品中心
  
纤维投料机Fiber batch feeder
 
创成纤维投料机是适应现代化工程建设的特殊性,而自主研制专用的新生设备,减少了劳动强度,大大地提高了工程质量。
  概述
  创成纤维投料机由投料系统、打散系统、输送系统、送料和控制系统等组成。
  一、投料系统:打开投料盖,即可轻松地将纤维投入料斗,启动适时计量。
  二、打散系统:将料斗的纤维进行打散,使其处于蓬松状态。
  三、输送系统:将处于蓬松状态的纤维,均匀地输送到送料口。
  四、送料系统:将送料的纤维,通过转动的风桶,将纤维源源不断送到由直径100cm的软管相连的拌和站。
  五、控制系统:由多种电器元件组成,设置了:计时计量、手动、自动、相序保护、过载保护等功能。
  操作程序:
  一、接通总电源前,将所有选择开关置于“关”的位置,接通总电源380v“相序,缺相保护”工作灯亮。否则应调整相序。
  二、自动控制:总电源开关接通20秒后,将“开关”旋置所需位置,设备即处于自动控制待命状态。
  三、手动控制:总电源开关接通20秒后,将状态开关旋置“手动”位置,即可自如地控制投料。
  四、设备运转过程中,遇特殊情况,自动报警,按下“应急”按钮,切断总电源。
  安全注意事项
  一、详细阅读使用说明书,安排专业安装和操作人员,进行设备调试。
  二、设备有相序,缺相保护,当连接的380v三相电源,相序错误或缺相时,设备不能正常工作。
  三、设备必须置于水平、硬质的基础上。
  四、设备运转时,严禁将人体部位及硬物置于料斗。
  五、定期(3—5天)给传动链加油,减速装置30天—50天换油,检查张紧轮是否松动。
  六、本机在出厂时各部都已调试好,不能轻易地调换风机,减速机的电源线预防错相造成反转,损坏机械,如确实需检修,应将传动链拆除后回观转向,确定准确无误方可安装使用。

类型

其他

型号

SMA全纤维CC-A800型

输送能力

0.06(t/h)

功率

8(KW)

输送距离

20(m)

外形尺寸

100*160*190(m)

       

  产品特性:
国家专利设计独特,安装快捷维修方便;
设备双向随可转换,各类纤维均可使用;
电子称重计量准确,无需增加干拌时间。

  技术参数:
规格:100*160*190 扬距:大于20米 仰高:大于15米
送料能力:0.8—1公斤/秒 功率:8千瓦
适用范围:
间歇式:最大可与5000型进口、国产间歇式沥青拌和站配套工作
连续式:最大可与1000吨/小时型进口连续式拌和站配套工作

Chuang Cheng fiber batch feeder is a newborn device which is self developed. It adapts to the particularity of modernized engineering construction, decreasing labor intensity and improving engineering quality greatly.
 
Overview:
Chuang Cheng Fiber Batch Feeder consists of feeding system, scattering system, delivery system, supplying system and command system, etc.
Feeding system:  Open the shield of the feeding machine, then cast the fiber into the bunker easily, and starts metering timely.
Scattering system: Scatter fiber in the bunker, in order to make it shaggy.
Delivery system: Deliver the shaggy fiber to the sending inlet uniformly.
Supplying system: Through the revolving wind barrel, send the fiber to the mixing station endlessly, which links to the wind barrel via flexible pipe whose diameter is 100cm.
Command system: It consists of various electrical components, and sets the following functions: measuring time and capacity, manual operation, automation, phase protection, and overload protection, etc.
Operating procedures:
1. Place all selection switches in the location of “off” before connecting the main power supply (380V), after which, the work lamp of “phase, lack of phase protection” should be lighted, otherwise, it’s necessary to adjust the phase.
2. Automatic controlling: after switch of the main power supply is connected by 20 seconds, turn the “on and off” switch to the position needed, then the device is on standby for automatic controlling.
3. Manual controlling: after switch of the main power supply is connected by 20 seconds, turn the state switch to the “manual” position, then the feeding process can be controlled easily.
4. When the device in the running process, if special cases occur, it will alerts automatically, and then you have to press the “emergency” button, and cut off the main power supply.
 
Safety notes:
1. Read the operation instructions carefully, arrange professional operators and installation staff to conduct debugging to the device.
2. The device has protective phase and lack of phase. When connecting three-phase power supply (380V), if the phase happens to be mistaken or in lacking condition, the device can’t work normally.
3. The device must be placed in the horizontal and rigid foundations.
4. When the device is working, it is strictly forbidden to locate parts of human body or hard objects on the bunker.
5. Append oil for the transmission chains periodically (three to five days), change oil for the speed reducer every thirty to fifty days, and check the tensile wheel to see whether it is loose or not.
6. Every part is debugged well when the machine gets out of the factory. The drawing fan can’t be substituted rashly. The power line of the speed reducer can prevent wrong phase that causes reversal rolling or damages to the machine. If it indeed requires inspection and repair, you should dismantle the transmission chains and check the diversion. After extremely accurate insurance, it can be installed and used.

Type
Others
Model type
SMA      Whole Fiber CC-A800
Delivery ability
0.06(t/h)
Power
8(KW)
Transmission distance
20(m)
External dimensions
100*160*190(m)

 
Characteristics of the product:
State patent and unique design, easy installation and convenient mending
Random duplex shift of the device, available to various fibers
Accurate metering by electronic weighing device, unnecessary to add dry mixing time
Technical parameters:
Specification:  100*160*190   
Tilt distance:  longer than 20m 
Heights of looking upon:  higher than 15m
Delivery ability:  0.8—1 kg/s      
Power:  8KW
Applicable scope:
Batch type:  In maximum, it can do the matching work with the batch-type (5000t) asphalt blending station imported or domestically produced.

Continuous type:  In maximum, it can do the matching work with continuous type (1000t) blending station imported.

 

版权所有:盐城市创成科技有限公司
地 址:盐城市沿河中路13号  中文域名:创成纤维  苏ICP备05010280号-1
会员客服
有事点这里